Two examples of the most common types of Voltage followers (buffers). You can find some theory behind them in our amplifier gain and buffer amplifier pages.
Transistor voltage follower:
This first circuit is a very simple one transistor voltage follower. Consist of two biasing resistors, and one other resistor at the emitter to acquire the output voltage from.
How it works:
The first to resistors connected to the transistor's base are forming a voltage divider, in order to set a biasing point for the transistor to work in our desired range. Then the transistor, our gain component for the circuit which in this case is only used as a gateway to isolate two circuit stages.
The resistor in the emitter is used to create a voltage from the current passing from the transistor; Without it we can't get any voltage as our output would be effectively shorted to ground (0 volts).
The capacitors that are displayed in the schematic are optional, but very useful to prevent a wrong operation of the circuit, specially in audio or high frequency uses. they stop any DC voltage to move or otherwise disrupt the bias point of the transistor, thus causing undesired operation. If you build this circuit only with dc remove the capacitors, as they will prevent the circuit from functioning under those conditions.
This circuit's operation is far more predictable and stable than the transistor version, and also requires less external components.
How it works:
Works as described above, no external elements to explain. This circuit uses feedback to maintain the voltage output the same as the input. Note that this schematic does not display power, ground and other connections for the op amp, these vary widely among manufacturers and op amps so refer to your op amp's datasheet for pinouts and power connections.
Electronic circuit diagrams and tutorials for beginners and hobbyists.
.
You can find many more electronic circuits for beginners by clicking the link!
Showing posts with label amplifier. Show all posts
Showing posts with label amplifier. Show all posts
Buffer amplifier
A buffer amplifier, or simply a buffer, is an electronic amplifier that is designed to have an amplifier gain of 1. Buffers are used in Impedance matching, the benefit of which is to maximize energy transfer between circuits or systems.
There are two main kinds of buffer circuits, Voltage buffers and Current buffers. The purposes of each is to isolate the mentioned characteristic to avoid loading the input circuit or source from the output stage.
Another name by which buffer amplifiers are known as is a voltage follower. The name is given because of the characteristic of the amplifier to output a signal of the same amplitude as the input (given the unity gain [gain of 1 or 0dB] ).
Examples of Buffer amplifiers:
The examples are too many to mention in this page, the most common being the transistor voltage follower and op amp version of it. The exact characteristics, formulas and construction instructions can be found on the specific component's page.
There are two main kinds of buffer circuits, Voltage buffers and Current buffers. The purposes of each is to isolate the mentioned characteristic to avoid loading the input circuit or source from the output stage.
Another name by which buffer amplifiers are known as is a voltage follower. The name is given because of the characteristic of the amplifier to output a signal of the same amplitude as the input (given the unity gain [gain of 1 or 0dB] ).
Examples of Buffer amplifiers:
The examples are too many to mention in this page, the most common being the transistor voltage follower and op amp version of it. The exact characteristics, formulas and construction instructions can be found on the specific component's page.
Amplifier Gain
This is one the main characteristics to determine when designing or choosing an amplifier. This is a measure of the increase (or decrease in case of negative gain) the amplitude of the input signal.
Representation:
There are a few different ways to represent amplifier gain. One of the more common way among beginners and hobbyists, specially for DC or small signals, is to describe gain as the ratio of input vs output amplitude:
Gain = Vout/Vin, Where both input and output are either voltage or current (amperage).
Another way to represent amplifier gain is using a logarithmic decibel scale (dB). This representation is calculated using the ratio of input/output powers using the formula:
Gain = 10log(Pout/Pin)
Utility of gain:
There are countless applications and uses for amplifiers, since in the electronics world most signals we get from sensors or transmission lines is very small. There are also other times when not the amplitude of the signal is required but its power to transform into useful work, like when powering a motor, transmitting a radio signal and displaying an image on a screen.
How to calculate:
The specifics of how much gain can an amplifier have depend heavily on the components or circuits used, as well as the topology (configuration) of the amplifier. You can have a better understanding of the formulas used for each component and configuration by going to the specific page.
Representation:
There are a few different ways to represent amplifier gain. One of the more common way among beginners and hobbyists, specially for DC or small signals, is to describe gain as the ratio of input vs output amplitude:
Gain = Vout/Vin, Where both input and output are either voltage or current (amperage).
Another way to represent amplifier gain is using a logarithmic decibel scale (dB). This representation is calculated using the ratio of input/output powers using the formula:
Gain = 10log(Pout/Pin)
Utility of gain:
There are countless applications and uses for amplifiers, since in the electronics world most signals we get from sensors or transmission lines is very small. There are also other times when not the amplitude of the signal is required but its power to transform into useful work, like when powering a motor, transmitting a radio signal and displaying an image on a screen.
How to calculate:
The specifics of how much gain can an amplifier have depend heavily on the components or circuits used, as well as the topology (configuration) of the amplifier. You can have a better understanding of the formulas used for each component and configuration by going to the specific page.
Amplifiers
Amplifiers increase either the amplitude (voltage) or power (Amperage/Current)
applied to its input.
Components of an amplifier:
Gain component: The main component of the amplifier, defines many of its characteristics like noise, bandwidth, gain, input and output impedance, and others.
Bias: Some types of components need a bias point in order to operate correctly. The bias point is a dc voltage applied to the input of the amplifier. There are many ways to set the bias point,
depending on the gain component used.
Accessories: These are many kinds of sub-circuits used to fine tune the operation of the amplifier, including preamplifiers, buffers, stabilizers, filters, limiters, etc..
Stages of Amplifiers:
Input: This stage consists of a signal from another subsystem outside the amplifier, or a sensor like a microphone, photodiode or any other component that delivers a small signal. Depending on
the intended purpose and input signal, this stage may contain a preamplifier, which is a signal (voltage) amplification before the main power (current) amplification stage, and a filter to
limit incoming frequencies.
Amplification: Main stage of any amplifier, most of the times it is a power amplification process, sometimes with signal amplification as well. This stage is where the gain component and many of the accessories like stabilizers and limiters are located.
Output: Last stage, sometimes consists of a buffer and/or filter to remove any noise generated in the main amplification stage. The buffer sometimes added to deliver more current (lower output impedance).

Block Diagram of a Amplifiers
(Click to enlarge)
applied to its input.
Components of an amplifier:
Gain component: The main component of the amplifier, defines many of its characteristics like noise, bandwidth, gain, input and output impedance, and others.
Bias: Some types of components need a bias point in order to operate correctly. The bias point is a dc voltage applied to the input of the amplifier. There are many ways to set the bias point,
depending on the gain component used.
Accessories: These are many kinds of sub-circuits used to fine tune the operation of the amplifier, including preamplifiers, buffers, stabilizers, filters, limiters, etc..
Stages of Amplifiers:
Input: This stage consists of a signal from another subsystem outside the amplifier, or a sensor like a microphone, photodiode or any other component that delivers a small signal. Depending on
the intended purpose and input signal, this stage may contain a preamplifier, which is a signal (voltage) amplification before the main power (current) amplification stage, and a filter to
limit incoming frequencies.
Amplification: Main stage of any amplifier, most of the times it is a power amplification process, sometimes with signal amplification as well. This stage is where the gain component and many of the accessories like stabilizers and limiters are located.
Output: Last stage, sometimes consists of a buffer and/or filter to remove any noise generated in the main amplification stage. The buffer sometimes added to deliver more current (lower output impedance).

Block Diagram of a Amplifiers
(Click to enlarge)
Description of Amplifier accessories:
Coupling: This is usually done with a capacitor. The purpose of the coupling capacitor is to prevent any DC voltage from modifying the bias point of the amplifier, to prevent clipping (driving the signal to the max voltage, distorting it) from a high or low bias point.
Another coupling method is using transformers. This is done on lower frequency signals where the reactance (resistance-like behavior when a component is applied an AC voltage) of capacitors is so high to the point the signal is practically lost.
A third choice is using tuned transformers, by using a capacitor in parallel with the transformer. This creates a tuned circuit that has a very narrow bandwidth, useful in some special interest amplifiers.
Filters: This topic is so extensive it deserves its own article. Amplifiers have uses for filters to limit noise and reject unwanted signals from its input. Combining a filter and an amplifier creates an active filter (filter that has gain).
Most filters use RC networks to create the filter, although RL or RLC are also used in some designs.
Stabilizers: This is usually some kind of feedback used to prevent clipping or other circuitry to keep the frequency within a certain range (stop frequency drifting).
Limiters: Sometimes only voltages up to a certain point are needed or desired, here limiters come into use. They limit or sometimes clip a signal if it goes above a certain voltage, other kind of limiters use feedback to control the gain of the amplifier so as to keep the output signal within the specified voltage range.
Buffers: Also called voltage followers, this is just another name for another stage of amplification with a gain of 1. This is to provide more current and avoid overloading the main amplifier, as doing so can reduce either the gain or bandwidth.
If you need a specific implementation of an amplifier circuit, you may want to consider learning all the abstract theory first and then moving on to the components page, where all component-specific circuits and modes of operation are listed.
Coupling: This is usually done with a capacitor. The purpose of the coupling capacitor is to prevent any DC voltage from modifying the bias point of the amplifier, to prevent clipping (driving the signal to the max voltage, distorting it) from a high or low bias point.
Another coupling method is using transformers. This is done on lower frequency signals where the reactance (resistance-like behavior when a component is applied an AC voltage) of capacitors is so high to the point the signal is practically lost.
A third choice is using tuned transformers, by using a capacitor in parallel with the transformer. This creates a tuned circuit that has a very narrow bandwidth, useful in some special interest amplifiers.
Filters: This topic is so extensive it deserves its own article. Amplifiers have uses for filters to limit noise and reject unwanted signals from its input. Combining a filter and an amplifier creates an active filter (filter that has gain).
Most filters use RC networks to create the filter, although RL or RLC are also used in some designs.
Stabilizers: This is usually some kind of feedback used to prevent clipping or other circuitry to keep the frequency within a certain range (stop frequency drifting).
Limiters: Sometimes only voltages up to a certain point are needed or desired, here limiters come into use. They limit or sometimes clip a signal if it goes above a certain voltage, other kind of limiters use feedback to control the gain of the amplifier so as to keep the output signal within the specified voltage range.
Buffers: Also called voltage followers, this is just another name for another stage of amplification with a gain of 1. This is to provide more current and avoid overloading the main amplifier, as doing so can reduce either the gain or bandwidth.
If you need a specific implementation of an amplifier circuit, you may want to consider learning all the abstract theory first and then moving on to the components page, where all component-specific circuits and modes of operation are listed.
Audio Amplifier
Here is a simple audio amplifier circuit that is easy to build and has few components. This circuit is built around the LM386 (click for datasheet) audio amplifier integrated circuit, useful when you need to power medium sized speakers from a music player that can only drive earphones.
How it works:
From left to right, the first part is the input stage, here is the connector to the audio source connected too the circuit using a capacitor. This capacitor passes only the audio, and blocks any direct current that may affect the function of the amplifier. Next to the capacitor is a variable transistor (potenciometer), this is used as a volume control.
Next is the LM386 itself, this amplifies the audio input using energy from the battery it is connected to. You'll notice there are two capacitors connected to it, one above and one below in the schematic. The top one is connected from pin 1 (positive side of capacitor) to pin 8 (negative side), this is to get the maximum amplification this IC can generate. The bottom one is also there to help get maximum amplification, this one goes connected from pin 7 (positive) to ground.
Last is the output stage, it is made with two capacitors, one resistor and the speaker. The resistor and capacitor that are connected before the speaker form a filter, that attenuates high frequency signals coming from the amplifier, most likely noise picked up or generated in the amplifying process. The capacitor connected to the speaker is there for the same reason we used a capacitor in the input stage, to prevent direct current from causing undesired operation of the speaker.
How it works:
From left to right, the first part is the input stage, here is the connector to the audio source connected too the circuit using a capacitor. This capacitor passes only the audio, and blocks any direct current that may affect the function of the amplifier. Next to the capacitor is a variable transistor (potenciometer), this is used as a volume control.
Next is the LM386 itself, this amplifies the audio input using energy from the battery it is connected to. You'll notice there are two capacitors connected to it, one above and one below in the schematic. The top one is connected from pin 1 (positive side of capacitor) to pin 8 (negative side), this is to get the maximum amplification this IC can generate. The bottom one is also there to help get maximum amplification, this one goes connected from pin 7 (positive) to ground.
Last is the output stage, it is made with two capacitors, one resistor and the speaker. The resistor and capacitor that are connected before the speaker form a filter, that attenuates high frequency signals coming from the amplifier, most likely noise picked up or generated in the amplifying process. The capacitor connected to the speaker is there for the same reason we used a capacitor in the input stage, to prevent direct current from causing undesired operation of the speaker.
Subscribe to:
Posts (Atom)
Welcome To Electronic Circuits For Beginners!
All circuits included here are recommended to be assembled in printed circuit boards. Printed circuit boards, or PCB's increase the circuit reliability and mechanical stability.
Circuits quick links:
-
-
-
-
-
-
Led chaser circuit-
-
-
Simple power supply-
Beginner Electronics mini course index
-
All circuits include parts list and complete How-it-works for beginners and hobbyists to easily understand.


