.
You can find many more electronic circuits for beginners by clicking the link!
Showing posts with label circuits. Show all posts
Showing posts with label circuits. Show all posts

H bridge circuit

An H bridge is a kind of circuit you use to control the direction (and sometimes speed) of an electric motor, using only a single polarity voltage (you need to reverse the way current flows in order to reverse the way the motor rolls).

How it works:

You have 4 transistors, wired as ON OFF switches. Two signal lines allow you to run the motor in one direction, when reversed, the motor runs in the other direction. It's very straightforward to use and build, but be careful to use only small motors, as the currents drawn from the bigger types can burn your components.

There are 3 modes of operation:
Both equal ( on or off ): motor doesn't run, as it's shorted or not connected
S1 on, S2 off: motor runs in reverse ( from negative [blue] to positive [red] )
S1 off, S2 on: motor runs normal.

Also note, unless you use power transistors, you need to connect diodes across the transistors in order to protect from overvoltages.

Simplified schematic:


Tone generator circuit

Simple, low component count tone generator. It can be adapted to create a morse code circuit, by adding a switch to the output.

How it works:

This circuit is based around the 555 timer circuit, used as an astable (free running) oscillator. The frequency (pitch) of the tone is set by the resistors and capacitors in the left side of the circuit. The first one is a potentiometer (variable resistor), this is our pitch control, which is basically all the external components you need. The capacitor to the far left is to reduce as much noise or undesired operation of the potentiometer, getting a smooth pitch change when adjusting.


You can find the timer's datasheet by following the link: 555 timer

Simple power supply

This circuit is very useful in beginners circuits, since most will work on 5v, which is the voltage of this easy little circuit.

How it works:

This circuit is just an implementation of the 7805 integrated voltage regulator. What this little component does is to lower a voltage and stabilize it by reducing noise and ripple, in order for circuits to have the constant voltage needed to work correctly



You can find the datasheet by following the link: 7805, take note of the typical applications notes, you can find some more uses for this versatile little regulator

Led Chaser

This Led chaser is built using some very common digital logic circuits. Easy to build, easy to work with, and looks amazing in the dark. This circuit will light each led in sequence, creating a moving light illusion.

How it works:

From left to right, the first IC is a binary counter, 74ls163, that is used to generate the address numbers we are going to use in the second part of the circuit, the demultiplexer 74ls138. This demux is the core of the circuit, as this IC pulls low the pin selected in the address inputs. Note that you need an external clock for the counter to work (count).

This is a very simple circuit to build, just take note of the control pins on each IC, since both have enable inputs for counting or output, but once set you don't need to worry about them. It can also be extended to 16 leds by using the Q3 output of the counter to control the enable inputs of a second demultiplexer, or just add a second one to generate a double pattern.



You can find the datasheets for both IC's by following the links: 74ls138 | | 74ls163

Voltage Follower Circuit

Two examples of the most common types of Voltage followers (buffers). You can find some theory behind them in our amplifier gain and buffer amplifier pages.

Transistor voltage follower:

This first circuit is a very simple one transistor voltage follower. Consist of two biasing resistors, and one other resistor at the emitter to acquire the output voltage from.

How it works:

The first to resistors connected to the transistor's base are forming a voltage divider, in order to set a biasing point for the transistor to work in our desired range. Then the transistor, our gain component for the circuit which in this case is only used as a gateway to isolate two circuit stages.

The resistor in the emitter is used to create a voltage from the current passing from the transistor; Without it we can't get any voltage as our output would be effectively shorted to ground (0 volts).

The capacitors that are displayed in the schematic are optional, but very useful to prevent a wrong operation of the circuit, specially in audio or high frequency uses. they stop any DC voltage to move or otherwise disrupt the bias point of the transistor, thus causing undesired operation. If you build this circuit only with dc remove the capacitors, as they will prevent the circuit from functioning under those conditions.


Transistor voltage follower

Op Amp Voltage Follower:

This circuit's operation is far more predictable and stable than the transistor version, and also requires less external components.

How it works:

Works as described above, no external elements to explain. This circuit uses feedback to maintain the voltage output the same as the input. Note that this schematic does not display power, ground and other connections for the op amp, these vary widely among manufacturers and op amps so refer to your op amp's datasheet for pinouts and power connections.




Opamp voltage follower

Audio Amplifier

Here is a simple audio amplifier circuit that is easy to build and has few components. This circuit is built around the LM386 (click for datasheet) audio amplifier integrated circuit, useful when you need to power medium sized speakers from a music player that can only drive earphones.

How it works:

From left to right, the first part is the input stage, here is the connector to the audio source connected too the circuit using a capacitor. This capacitor passes only the audio, and blocks any direct current that may affect the function of the amplifier. Next to the capacitor is a variable transistor (potenciometer), this is used as a volume control.

Next is the LM386 itself, this amplifies the audio input using energy from the battery it is connected to. You'll notice there are two capacitors connected to it, one above and one below in the schematic. The top one is connected from pin 1 (positive side of capacitor) to pin 8 (negative side), this is to get the maximum amplification this IC can generate. The bottom one is also there to help get maximum amplification, this one goes connected from pin 7 (positive) to ground.

Last is the output stage, it is made with two capacitors, one resistor and the speaker. The resistor and capacitor that are connected before the speaker form a filter, that attenuates high frequency signals coming from the amplifier, most likely noise picked up or generated in the amplifying process. The capacitor connected to the speaker is there for the same reason we used a capacitor in the input stage, to prevent direct current from causing undesired operation of the speaker.

amplifier circuit using 386 electronic circuit
(click to enlarge)

Led Flasher Circuit

This circuit is built around one of the most popular timer integrated circuits, the 555 timer.

This circuit will flash the led on and of at regular intervals.

How it works:

From left to right, the two resistors and the capacitor set the time it takes to turn the led on or off, by changing the time it takes to charge the capacitor to trigger the timer. Next is the 555 timer, this is where all the work gets done to determine the time the led stays on and off. It contains a complicated circuit inside, but since it is packaged in the IC it can be used as a simple component.

The two capacitors that are right of the timer are just accessories so to speak, but are needed for the timer to work correctly. The last part is the resistor and the led, the resistor is there to limit the current on the led so that it won't burn.

555 led flasher circuit
(click to enlarge)

(click to enlarge)
(pin numbers on actual IC)

Simple FM Transmitter

This circuit uses a small microphone to capture the sound and some transistors to generate radio waves that can be picked up by a FM receiver like a car stereo.

How it works:

From left to right, the first part is the microphone and some resistors to get it working. Next we have a capacitor and the first transistor, this amplifies the sound from the microphone so that it can be loud enough to work with. The last part, there is a transistor, a coil and some capacitors. This part generates the radio waves and combines them with the sound from the mic to transmit it thru the antenna.

The coil is made with about 9 turns of wire, use a pencil to get the right diameter for the coil. The capacitor with the arrow is called a trimmer capacitor, it has a small screw to adjust the value, we'll use it to tune a certain frequency or station to transmit on.

simple fm radio transmitter(click to enlarge)

Welcome To Electronic Circuits For Beginners!

All circuits included here are recommended to be assembled in printed circuit boards. Printed circuit boards, or PCB's increase the circuit reliability and mechanical stability.

Circuits quick links:

-

Simple FM Transmitter

-

Led Flasher Circuit

-

Quadrocopters for beginners

-

Voltage follower circuit

-

Beginners Audio Amplifier

-

Led chaser circuit

-

Tone generator circuit

-

H bridge circuit

-

Simple power supply

-

Beginner Electronics mini course index

-

All circuits include parts list and complete How-it-works for beginners and hobbyists to easily understand.